BS 1449-2-1983
|
ID： |
05C2730683354CEF9642E7001954C19E |
|
文件大小(MB)： |
0.21 |
|
页数： |
14 |
|
文件格式： |
|
|
日期： |
2013-6-1 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BRITISH STANDARD BS 1449-2:,1983,(Incorporating,Amendment Nos. 1, 2,3 and 4),Steel plate, sheet and,strip —,Part 2: Specification for stainless and,heat-resisting steel plate, sheet and,strip,UDC 669.14.018.4.018.8 – 41,Licensed Copy: Blind Login, Messier Dowty France, Thu Dec 21 03:36:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI,BS 1449-2:1983,This British Standard, having,been prepared under the,direction of the Iron and Steel,Standards Committee, was,published under the authority,of the Board of BSI and comes,into effect on,31 May 1983,. BSI 09-1999,First published August 1948,First revision January 1956,First published as Part 4,December 1967,First published as Part 2,August 1975,First revision as Part 2,May 1983,The following BSI references,relate to the work on this,standard:,Committee reference ISM/10,Draft for comment 81/75414 DC,ISBN 0 580 11962 9,Committees responsible for this,British Standard,This British Standard was published under the direction of the Iron and Steel,Standards Committee ISM/-. Its preparation was entrusted to Technical,Committee ISM/10 upon which the following bodies were represented:,Cold Rolled Sections Association,British Internal Combustion Engine Manufacturers’ Association,British Railways Board,British Steel Industry,Institution of Production Engineers,Society of Motor Manufacturers and Traders Limited,The following bodies were also represented in the drafting of the standard,through subcommittees and panels:,Institute of Sheet Metal Engineering,National Association of Steel Stockholders,Process Plant Association,Stainless Steel Fabricators’ Association of GB,Amendments issued since publication,Amd. No. Date of issue Comments,4807 May 1985,6646 April 1991,8828 December 1995,9648 September 1997 Indicated by a sideline in the margin,Licensed Copy: Blind Login, Messier Dowty France, Thu Dec 21 03:36:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI,BS 1449-2:1983,. BSI 09-1999 i,Contents,Page,Committees responsible Inside front cover,Foreword ii,Section 1. General requirements,1.1 Scope 1,1.2 Definitions 1,1.3 General 1,1.4 Information to be supplied by the purchaser 1,1.5 Steelmaking process 3,1.6 Freedom from defects 3,1.7 Surface finishes 3,1.8 Condition of material on delivery 3,1.9 Edge conditions 3,1.10 Chemical composition 4,1.11 Testing and manufacturers certificate 4,1.12 Retests 5,1.13 Reheat treatment 6,1.14 Marking 6,1.15 Inspection 6,1.16 Testing facilities 6,Section 2. Specific requirements,2.1 Chemical composition 6,2.2 Mechanical properties and delivery condition 6,2.3 Intergranular corrosion test 6,Section 3. Tolerances on dimensions and shape,3.1 General 7,3.2 Non-continuously hot rolled flat products (quarto plate) 7,3.3 Hot rolled wide strip in coils, or sheet/plate cut from coils,or coils slit from wide strip. 7,3.4 Hot rolled narrow strip 7,3.5 Cold rolled sheet/plate, cold rolled coil and slit coil,(rolled width 600 mmor above) 7,3.6 Cold rolled narrow strip (rolled width less than 600 mm),cut lengths and strip slit from narrow strip 7,Table 1 — Surface finishes 2,Table 2 — Permitted product analysis deviations from the,specified composition 4,Table 3 — Acceptance units for test by lot or batch 5,Table 4 — Chemical composition limits based on cast analysis 6,Table 5 — Mechanical properties, softening temperatures and,details of intergranular corrosion test of austenitic stainless steels 7,Table 6 —Table deleted,Publications referred to Inside back cover,Licensed Copy: Blind Login, Messier Dowty France, Thu Dec 21 03:36:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI,BS 1449-2:1983,ii . BSI 09-1999,Foreword,This Part of BS 1449, prepared under the direction of the Iron and Steel,Standards Committee, is a revision of BS 1449-2:1975 which is withdrawn.,It constitutes a general updating of the requirements for stainless and,heat-resisting steels, in line with moves towards international harmonization of,these materials.,Included for the first time are definitions, based on those agreed internationally,for the terms used and, additionally, a clause for the identification and marking,of the material. The tabular presentation of the specific requirements for,particular steel grades has been simplified.,The other Part of this standard is:,— Part 1: Specification for carbon steel plate, sheet and strip.,For corrosion and heat-resisting stainless steel plates for fired and unfired,pressure vessels, reference should be made to BS 1501-3, and for stainless steel,strip for springs, reference should be made to BS 5770-4.,This Part of BS 1449 has been amended to take into account the publication of the,following European Standards:,EN 10……
……